A pit that is filling and not emptying is the one to deal with now
Start with the simple things. Look at the plug and the outlet the pump uses, and check the breaker for that circuit. If the pump has its own float switch on a cord, see whether it is caught against the side of the pit. Unplug the pump before you reach into the pit for anything, and if the water is near an outlet or an extension cord, stay out of it and turn off the breaker.
Then move boxes and anything electrical off the basement floor near the pit. Water in a sump is groundwater from the weeping tile around the foundation, so turning off taps in the house will not slow it down. A full pit that is still rising cannot wait; a pump that is running but sounds rough usually can wait for a booked visit.
If the water is coming up through the floor drain rather than the sump, the cause is different. That points to the sewer side of the house, and drain cleaning or sewer repair is the place to start.
Each sound and pattern points to a different fault
A pump that switches on and off every few seconds is usually a float set too low or a check valve that lets the discharge water fall back into the pit. A pump that runs and runs without the level dropping often has a jammed impeller, a blocked intake screen or a discharge line frozen or crushed outside.
A hum with no water moving means the motor is getting power but the impeller is not turning. A loud rattle or clunk when it stops is often the check valve slamming shut. A musty smell from the pit is usually a dry pit with no lid, and a sealed cover fixes it.
At the pit, these are easy to tell apart. We lift the pump, watch a full cycle and tell you which part has failed and whether the pump is worth keeping.
Which Tavistock houses rely on a sump
Most of the houses in Taylor Heights, on Janelle Drive and Lunor Court, and in The Orchards along Fred Krug Avenue drain their foundation weeping tile to a sump pump. Many of those pumps have run since the house was built, and a pump that has never been looked at tends to fail on the wettest night of the year.
In the Ben-Der Subdivision, around Bender Avenue, Homewood and Westwood, the weeping tile is sometimes tied to a sump and sometimes to the sewer, so the first step is finding out which your house has. The oldest houses on the original village streets, such as Hope Street West and Woodstock Street North, usually have a floor drain tied to the sewer and no sump at all.
Tavistock's wastewater runs through a separated collection system, and Oxford County's sanitary sewer design guidelines do not permit foundation drains, weeping tile or roof drainage to connect to the sanitary sewer. A sump discharge goes outside onto the lot, never into a laundry tub or a floor drain. If yours is piped into the house drains, we will show you where and explain the change.
Battery backup keeps the pit emptying through a power cut
The night a sump is needed most is often the night a storm takes the power out. A battery backup pump sits in the same pit, a little higher than the main pump, and takes over when the main pump stops or cannot keep up. It runs on its own battery and sounds an alarm so you know it has started.
We size the backup to the pit and the height the water has to be lifted, fit its own check valve, and show you how to test it and when the battery is due for replacement. Battery life depends on the battery itself, so read the manufacturer's warranty terms and note the install date on the case.
Test the pump before the spring melt
Snowmelt and spring rain are when the weeping tile carries the most water. Before then, take the lid off the pit and slowly pour in a bucket of water until the float rises. The pump should start, empty the pit and stop cleanly. Walk outside and check that water comes out at the end of the discharge line and drains away from the foundation.
If the pump does not start, starts late, or the outside line is blocked by ice or soil, book a visit while the ground is still dry. A pump that passes the bucket test can usually wait until something changes.
How a sump pump visit goes
We ask what the pump has been doing and when it started, then test it with water in the pit and look at the float, the check valve, the discharge line and the outlet it plugs into. You get a written price for repair or replacement and approve it before anything is fitted.
A replacement pump is matched to the pit and the flow your weeping tile carries, not simply to the label on the old one. We fit a new check valve, seal the lid and confirm the discharge runs outside. Work is performed by licensed plumbers (306A Certificate of Qualification). If a job involves new drain connections, a building permit may be needed, and the municipal building department decides that. Our guide on doing your own plumbing in Ontario covers when that applies.
