A leaking tank or a smell of gas comes first
If water is pooling under the tank, find the cold water valve on the pipe at the top of the heater and turn it clockwise until it stops. For an electric heater, switch off its breaker at the panel. For a gas heater, turn the control knob to off or pilot. That stops the tank refilling and keeps the elements or burner from firing on an empty tank. Move boxes off the floor and leave the rest for the plumber.
If you smell gas near the heater, do not touch switches or try to relight anything. Leave the house and call your gas supplier's emergency number from outside. That is the one water heater problem that cannot wait for a plumber's visit.
A slow drip from the relief valve pipe, or a little water at a fitting, is worth a call but rarely an emergency. Put a pail under it and keep using the heater until we look.
No hot water usually has a simple cause
On an electric tank, the most common causes are a tripped breaker, a reset button on the heater that has popped, or a failed element or thermostat. Checking the breaker is safe. Removing the access panels is not, because the wiring behind them is live.
On a gas tank, the usual culprits are a pilot that has gone out, a worn thermocouple or a faulty gas control. Relighting a pilot by following the label on the tank is fine if you are comfortable doing it. If it will not stay lit, stop there and call.
Lukewarm water that runs out quickly, or hot water that smells of rotten eggs, can wait a few days. Both are worth looking at, but neither is unsafe in the meantime.
Groundwater scale shortens the life of tanks and tankless units
Tavistock's municipal water, like the rest of Oxford County's systems, comes from groundwater in underground aquifers. Groundwater carries dissolved minerals, and heating it drops them out as scale. In a tank, the scale settles on the bottom, where it rumbles and pops as the burner or element heats through it. It also takes up space, so the tank holds less hot water than it should.
Tankless heaters feel it differently. Scale builds inside the heat exchanger, and the unit starts showing error codes, cutting out mid-shower or struggling to keep temperature. Regular descaling keeps most tankless units running well, and skipping it shortens their life.
The newer houses in Taylor Heights and The Orchards often show this early, on heaters and fixtures that are not old at all. If your heater is scaling quickly, a water softener in front of it can slow the build-up. We will tell you whether that is worth it for the house as a whole, as well as for the heater.
We test before we recommend repair or replacement
A noisy tank is not always a dying tank. We check the age on the label, the condition of the anode rod, the amount of sediment, the relief valve and the venting. On a tankless unit we read the error history and check the flow and the heat exchanger.
Then we tell you plainly which it is. A thermostat, element, thermocouple or anode can often be replaced and the heater will carry on. A tank leaking from its seams or base cannot be repaired and has to be replaced. If the heater is still under the manufacturer's warranty, keep the receipt and the serial number handy, because some parts may be covered.
Either way, you see the number in writing and approve it before any part is fitted.
Replacements are sized to the household and set to a safe temperature
When a heater does need replacing, we size it to how many people live in the house and how they use hot water, rather than copying whatever the old label said. We go through tank and tankless, electric and gas, and what each means for your space, venting and running costs, so the choice is yours.
Ontario's Building Code (Part 7, Article 7.2.10.7.) limits the water coming from a shower head or into a bathtub to 49 °C. The tank itself is often set hotter, so we check that a mixing valve or the fixture controls keep the water at the tap within that limit. That matters most in houses with young children or older relatives.
Work is performed by licensed plumbers (306A Certificate of Qualification). Gas work is performed by TSSA-certified gas technicians. If you are wondering what you can do yourself, our guide on doing your own plumbing in Ontario sets out the rules.
How a water heater visit goes
When you call, we ask what the heater is doing, whether it is electric or gas, tank or tankless, and roughly how old it is. If there is a leak, we tell you what to shut off while you wait.
On the visit, the plumber tests the heater, explains what was found and gives you a written price for the repair or the replacement. Nothing is fitted until you approve it. On a replacement, we drain and remove the old tank, connect the new one, check for leaks, set the temperature and show you where the shut-off and the controls are, so you know what to do if anything changes. You can book a visit or ask for a price.
